Installation freezes (blank screen) after the install kernel is loaded on a system which uses an nVidia video KEYWORDS: openserver open server ose 506 5.0.6 507 5.0.7 nvidia video invd oss661a btld fd.legacy geforce chips toshiba ENGREF fz528031 528031 ERGREF erg712343 712343 RELEASE: SCO Openserver System Release 5.0.7, 5.0.6 PROBLEM: I am trying to install SCO OpenServer on a system which uses an nVidia video chip. During the installation the system just freezes (blank screen) after the install kernel is loaded. It seems that the nVidia video chip does not switch to VGA mode once the OSr5.0.x install kernel is loaded. This problem was first observed on several models of Toshiba laptop using nVidia GeForce 4xx Go video chips. However, according to nVidia this problem could have occurred with certain video BIOS revisions on a variety of different nVidia video chips. HARDWARE: Toshiba laptops using nVidia GeForce 4xx Go video chips CAUSE: The problem is caused by an interaction between the OSR5 VGA driver and the video BIOS. The VGA driver programs video modes using an old table of mode data located within the video BIOS. This mode table was first introduced in the IBM EGA, and is not used by most current operating systems nor by the video BIOS itself. Two operating systems which do still use it are SCO OpenServer and SCO UnixWare. To save ROM space, some recent nVidia BIOS revisions omit this table. The VGA driver should be able to recognize that this table is absent, but it cannot. Instead, it reads wrong, unrelated data out of the BIOS, and programs it into the VGA registers. The result is either a completely blank screen, or (in some cases) a system crash requiring a reboot. SOLUTION: Support Level Supplement (SLS) OSS661A, the Video BIOS Compatibility Supplement for OpenServer5 addresses this issue. Software Notes and Recommendations ---------------------------------- SLS OSS661A can be used with: SCO OpenServer Release 5.0.7 SCO OpenServer Release 5.0.6 1. Download the OSS661A installation notes file from: ftp://ftp.sco.com/pub/openserver5/oss661a.ltr a) Change directory to the patch storage area: # cd /local/patches If this directory does not exist on your system, create it as follows: # mkdir /local/patches # chmod 700 /local/patches b) Download the OSS661A media image file from: ftp://ftp.sco.com/pub/openserver5/oss661a.btld.Z to the patch storage area (/local/patches). Then extract it to a formatted floppy with this command: # zcat /local/patches/oss661a.btld.Z > /dev/fd0 2. Boot from OpenServer 5.0.x install media with bootstring: Boot : defbootstr link=invd prompt If a second BTLD is required for the machine's host adapter, the syntax is: link="invd other" If the machine's floppy drive is a USB drive, add "fd.legacy=0" to the bootstring. For example, Boot : defbootstr link="invd ad320" fd.legacy=0 prompt You are prompted for the BTLD floppy: Please insert the fd(65)invd volume and press , or 'q' to quit: Provide a floppy containing the BTLD when prompted. When the driver has been linked, the following prompt appears: System loaded, press to start: Check for BTLD error messages (there shouldn't be any). Hit . The kernel clears the screen and starts displaying hardware information. Install normally. After hardware information is displayed the screen goes blue and you are prompted for the BTLD disk a second time: Please insert (invd) package BTLD disk into the floppy drive so that it can be extracted onto the hard disk for incorporation into the link-kit. Press ENTER for OK. If the machine has a USB floppy and "fd.legacy=0" was not entered, this is the point at which the install fails, giving: Preparing root filesystem ... Done. The BTLD packages will now be extracted. mount: Bad address Please select the floppy drive you are using: (1) /dev/fd0 (2) /dev/fd1 When installation is complete, the system should boot from the hard disk and behave normally. If you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier. NOTES: If after selecting /dev/fd0 or /dev/fd1 you get the following: ----- Please insert the floppy for BTLD package: invd and press : mount: Bad address Could not mount the BTLD floppy You may: (a) Try again (b) Abort BTLD load, but continue installation (c) Abort the installation Respond with one of (a,b,c): ----- Then it is likely that you have selected "fd.legacy=0" but you do not have a floppy disk connected via USB. SEE ALSO: ftp://ftp.sco.com/pub/openserver5/oss661a.btld.Z