Dear SCO Customer, Support Level Supplement (SLS) OSS648C, the Processor and SMP Supplement for OpenServer 5.0.6, addresses the following problems and changes: 1) On some multiprocessor systems the driver for a PCI card with a PCI-to-PCI bridge onboard was unable to register its interrupt. Note: The following fixes were also included in SLS OSS648B: 2) On a multiprocessor system PCI interrupt sharing was failing when one or more of the drivers sharing an interrupt was able to handle the interrupt on any processor. Symptoms of this problem included spurious and lost interrupts. Note: The following fixes were also included in SLS OSS648A: 3) On a multiprocessor system with fast processors, the auxiliary processor was timing out with the error message "WARNING: CPU2 did not finish boot code". This solution only applies if SMP is installed. 4) A Pentium 4 processor was running with a 50% duty cycle. 5) Pentium 4 processor thermal management is initialized. 6) Adds processor recognition for newer Pentium III models, and Intel NetBurst microarchitecture Pentium 4 and Intel Xeon processors. 7) Adds support for Pentium 4 machine check handling. 8) Adds newer Pentium III and Pentium 4 processors and Pentium 4 Model Specific Registers to the "hw -v -rcpu" command. 9) Adds enhancements for displaying Model Specific Registers for the "hw -v -rcpu" command. 10) Adds enhancements and fixes for the "hw -v -rpci" command. SLS OSS648C updates these files: /etc/conf/pack.d/apic/Driver.o /etc/conf/pack.d/apic/space.c /etc/conf/pack.d/crllry/Driver.a /etc/conf/pack.d/crllry/space.c /etc/conf/pack.d/mpsw/Driver.o /etc/conf/pack.d/kernel/os.a /etc/conf/pack.d/pci/Driver.o /etc/hw Software Notes and Recommendations ---------------------------------- SLS OSS648C should only be installed on: SCO OpenServer Release 5.0.6 with Release Supplement 506A (rs506a) WARNING: Do not run OpenServer on systems with the Intel NetBurst microarchitecture Pentium 4 or Intel Xeon processor without Release Supplement 506A. Doing so might damage your hardware. For further information, see the "Release and Installation Notes" for "Release Supplement 5.0.6A for OpenServer 5". This document is available from: ftp://ftp.sco.com/pub/openserver5/rs506a/rs506a.txt Installation Instructions ------------------------- 1. Download the OSS648C media image file from: ftp://ftp.sco.com/pub/openserver5/oss648c Place the file in the /tmp directory, and rename the file by typing the command: mv /tmp/oss648c /tmp/VOL.000.000 2. Run the Software Manager with the command: # scoadmin software or double-click on the Software Manager icon in the desktop. 3. Pull down the "Software" menu and select "Install New". 4. When prompted for the host from which to install, choose the local machine and then "Continue". 5. In the "Select Media" menu, pull down the "Media Device" menu. Select "Media Images", then choose "Continue". 6. When prompted for the "Image Directory", enter "/tmp" (or the directory where you placed the VOL file in step 1) and choose "OK". 7. When prompted to select software to install, make sure that the "OSS648C" entry is highlighted. Choose "Install". 8. Installation of SLS OSS648C is now complete. To exit the Software Manager, select "Exit" from the "Host" menu. 9. A kernel relink occurred during this process and it will be necessary to reboot the server for the supplement to take effect. Removal Instructions -------------------- Note: Patches must be rolled back in the reverse order in which they were installed on a per-component basis. To remove SLS OSS648C from SCO OpenServer 5.0.6, follow these steps: 1. Log in as root. 2. Execute the command: # scoadmin software or double-click on the Software Manager icon in the desktop. 3. Highlight "OSS648C: Processor and SMP Supplement for OpenServer 5.0.6". 4. Pull down the "Software" menu and select "Remove Software". 5. Once the removal finishes, quit the Software Manager. Removal of SLS OSS648C is now complete. 6. A kernel relink occurred during this process and it will be necessary in order to reboot the server. If you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier.