Dear SCO Customer, Support Level Supplement (SLS) OSS602B, the Virtual Disk Manager Supplement for OpenServer Release 5, addresses the following known issues with the Virtual Disk Manager on SCO OpenServer 5: 1. A problem of system hangs during shutdown caused by uncompleted disk transactions. The hang has been known to occur at the "The system is down" message, specifically at the "dkconfig -h halt" process in /etc/rc0.d/K81VDRESTORE. SLS OSS602B adds a timeout to insure that during a shutdown the Virtual Disk Manager will not hang the system. Additional problem corrected in SLS OSS602B: 2. Rebuilding a failed RAID level 5 Virtual Disk causes an OpenServer 5.0.5 system to panic. The panic has been known to occur approximately one minute after this message at system initialization: 'Queuing virtual disk restores for vdisk4' or following a 'dkconfig -r' or 'dkconfig -R' command, due to a call being made to the hardware driver with masked interrupts. Installation Instructions ------------------------- 1. Download the OSS602B media image file (oss602b file), place the file in the /tmp directory rename the file by typing these commands: mv /tmp/oss602b /tmp/VOL.000.000 2. Run the Software Manager with the command: # scoadmin software or double-click on the Software Manager icon in the desktop. 3. For SCO OpenServer 5.0.4 or 5.0.5, pull down the "Software" menu and select "Install New". For SCO OpenServer 5.0.0 or 5.0.2 or SCO Internet FastStart 1.x, pull down the "Software" menu and select "Patch Management --> Apply Patch". 4. When prompted for the host from which to install, choose the local machine and then "Continue". 5. In the "Select Media" menu, pull down the "Media Device" menu. Select "Media Images", then choose "Continue". 6. When prompted for the "Image Directory", enter "/tmp" (or the directory where you placed the VOL file in step 1) and choose "OK". 7. For SCO OpenServer 5.0.4 or 5.0.5, when prompted to select software to install, make sure that the "OSS602B" entry is highlighted. Choose "Install". For SCO OpenServer 5.0.0 or 5.0.2 or Internet FastStart 1.x, when prompted to select installation type, choose "Full". 8. Installation of SLS OSS602B is now complete. To exit the Software Manager, select "Exit" from the "Host" menu. 9. A kernel relink occurred during this process, and it will be necessary to reboot the server for the supplement to take effect. Removal Instructions -------------------- Note: Patches must be rolled back in the reverse order in which they were installed on a per-component basis. That is, if OSS602B is not the most recent patch applied to the UNIX component of the product, you will have to roll back all patches applied after OSS602B prior to rollback of the OSS602B patch. To remove SLS OSS602B from SCO OpenServer 5.0.4 and 5.0.5, take these steps: 1. Log in as root. 2. Execute the command: # scoadmin software or double-click on the Software Manager icon in the desktop. 3. Highlight "OSS602B: Virtual Disk Manager Supplement". 4. Pull down the "Software" menu and select "Remove Software". 5. Once the removal finishes, quit the Software Manager. Removal of SLS OSS602B is now complete. 6. Because kernel relink occurred during this process, it will be necessary to reboot the server. To remove SLS OSS602B from SCO OpenServer 5.0.0, 5.0.2 and Internet FastStart 1.0, 1.1, take these steps: 1. Log in as root. 2. Execute the command: # scoadmin software or double-click on the Software Manager icon in the desktop. 3. To roll back this patch, pull down the "Software" menu and select "Patch Management-->Rollback Patch". 4. Take these steps: a. You will see the "Begin Rollback Patch" menu and will be asked to select patched software to roll back. Select "SCO UNIX System V Operating System" and choose "Continue". b. You will see the "Patch Selection" window. Make sure that OSS602B is selected. Choose "Continue". c. You will see the "Confirm Selected Patches" window. Choose "Rollback" to confirm removal of OSS602B. d. You will see the "Rollback Progress" window, as the system performs the rollback of the patch, and finally a "Rollback Complete" window when the rollback is finished. 5. Exit the Software Manager by choosing "Exit" from the "Host" menu. Removal of SLS OSS602B is now complete. 6. Because a kernel relink did occur during this process, it will be necessary to reboot the server. If you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier.