Dear SCO Customer, The enclosed Support Level Supplement (SLS) OSS473A, the SCOterm Security Supplement, corrects a vulnerability in the scoterm program. SLS OSS473A is intended for use on these products: SCO OpenServer Host System Release 5.0.0, 5.0.2, 5.0.4 SCO OpenServer Desktop System Release 5.0.0, 5.0.2, 5.0.4 SCO OpenServer Enterprise System Release 5.0.0, 5.0.2, 5.0.4 SCO OpenServer Internet FastStart Release 5.0.4 SCO Internet FastStart Release 1.0.0, 1.1.0 Note: SLS OSS473A may be installed on OpenServer Release 5.0.4 either with or without Release Supplement 504C (rs504c) installed on the system. I. INSTALLING SLS OSS473A 1. Prepare the media for installation. Download the OSS473A media image file (oss473a.Z file), place the file in the /tmp directory, uncompress and rename the file by typing the following commands: uncompress /tmp/oss473a.Z mv /tmp/oss473a /tmp/VOL.000.000 2. Run the Software Manager with the command: # scoadmin software or double-click on the Software Manager icon in the desktop. 3. For SCO OpenServer 5.0.4, pull down the "Software" menu and select "Install New". For SCO Internet FastStart 1.x, and SCO OpenServer 5.0.0 or 5.0.2, pull down the "Software" menu and select "Patch Management --> Apply Patch". 4. When prompted for the host from which to install, choose the local machine and then "Continue". 5. When prompted to select the media device: If you are installing this SLS from diskette media, select the appropriate floppy disk drive and then "Continue". Proceed to step 6. If you are installing this SLS from media images per step 1, select "Media Images", then "Continue". When prompted for the "Image Directory", enter "/tmp" (or the directory where you placed the VOL file in step 1) and then select "OK". 6. For SCO OpenServer 5.0.4, when prompted to select software to install, ensure that the "OSS473A" entry is highlighted. Choose "Install". For Internet FastStart 1.x, OpenServer 5.0.0 or 5.0.2, when prompted to select installation type, choose "Full". NOTE: If you have installed the scoterm binary from sse009, you may get a verification error during the installation of OSS473A. If you do, you may safely ignore this error message and continue the installation. 7. Once the installation finishes, quit the Software Manager. Installation of SLS OSS473A is now complete. II. REMOVING SLS OSS473A Note: Patches must be rolled back in the reverse order in which they were installed on a per-component basis. The OSS473A SCOterm Security Supplement consists of a patch to the BaseX component. If this component was patched after OSS473A was installed, then you will have to roll back the later patch before you can roll back the SLS OSS473A patch. IIa. Removing SLS OSS473A from SCO OpenServer 5.0.4 1. Log in as root. 2. Execute the command: # scoadmin software or double-click on the Software Manager icon in the desktop. 3. Highlight "OSS473A: SCOterm Security Supplement for SCO OpenServer Release 5". 4. Pull down the "Software" menu and select "Remove Software". 5. Once the removal finishes, quit the Software Manager. Removal of SLS OSS473A is now complete. You must reboot your system for the removal to take effect. IIb. Removing SLS OSS473A from SCO OpenServer 5.0.0, 5.0.2 and Internet FastStart 1.0, 1.1 1. Log in as root. 2. Execute the command: # scoadmin software or double-click on the Software Manager icon in the desktop. 3. SLS OSS473A patches the software component SCO BaseX. To roll back this patch, pull down the "Software" menu and select "Patch Management-->Rollback Patch". 4. Take these steps: a. You will see the "Begin Rollback Patch" menu and will be asked to select patched software to roll back. Select "Standard X Clients" and choose "Continue". b. You will see the "Patch Selection" window. Make sure that OSS473A is selected. Choose "Continue". c. You will see the "Confirm Selected Patches" window. Choose "Rollback" to confirm removal of OSS473A. d. You will see the "Rollback Progress" window, as the system performs the rollback of the patch, and finally a "Rollback Complete" window when the rollback is finished. 5. Exit the Software Manager by choosing "Exit" from the "Host" menu. Rollback of OSS473A is now complete. If you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier. We appreciate your business. SCO Support Services