Dear SCO Customer, The enclosed Support Level Supplement (SLS) OSS452A, prevents a panic with the panic message: PANIC: k_trap kernel mode trap type 0x0000000F which is known to occur on Pentium Pro machines, most notably while printing to a parallel port. It is most frequently associated with running SCO OpenServer 5.0 on a single CPU without SCO SMP on a machine containing an APIC chipset and multiple CPUs. At this point, the occurrence of a trap F can be considered to be a spurious event of no special significance to the operating system. This patch resolves the issue by acting on an occurrence of a trap F event in a manner other than panicking the system. When the patch is applied, the response of the kernel to a trap F becomes tunable. The description below of the tunability is appended to the file /etc/conf/pack.d/kernel/space.c. By default, the tunable variable trapf_action is set to 2: /* TRAP_F_PATCH * The setting of trapf_action defines the behavior in the * event of a the kernel receiving a Trap F. Note that this * should never happen, and is probably the result of a * hardware problem with your system. Appropriate action * should be taken to trace and rectify the fault. The * following actions may be taken on receipt of a Trap F: * * trapf_action action * ---------------------------------- * 0 PANIC the kernel * 1 consume the Trap F silently * 2 report the error first time only * 3 report the error every time */ int trapf_action = 2; /* TRAP_F_PATCH */ If desired, the value of trapf_action may be modified to take on the values 0, 1, or 3. Relink the kernel and reboot for the changes to take effect. Note: Instead of applying this patch, a BIOS fix from the BIOS manufacturer may be obtained. This is most highly recommended, as it will prevent these spurious trap F events from occurring. Also, in the upcoming release of SCO OpenServer 5, the response of the kernel to a trap F will not be tunable, and will be as if trapf_action is set to the value 3. RELEASE INFORMATION SLS OSS452A is intended for use on these products: SCO OpenServer Enterprise System Release 5.0.0, 5.0.2 SCO OpenServer Desktop System Release 5.0.0, 5.0.2 SCO OpenServer Host System Release 5.0.0, 5.0.2 SCO Internet FastStart Release 1.0.0, 1.1.0 INSTALLATION AND REMOVAL INSTRUCTIONS Installing patches on SCO OpenServer 5.0.x usually consists of two phases: "Loading" and "Applying". The instructions that follow enable you to both install the patch from distribution media or media image, as well as configure the patch to be installed from a remote SCO OpenServer 5.0.x system over a TCP/IP network. I. LOADING THE PATCH 1. Log in as root. 2. If you are installing this SLS from a media image, there is a file called oss452a.Z. Uncompress this file with this command: # uncompress oss452a.Z Copy the file to the /tmp directory and name it VOL.000.000: # cp oss452a /tmp/VOL.000.000 If you are installing this SLS from floppy disk media, skip this step and proceed to step 3. 3. Execute the command: # scoadmin software or double click on the Software Manager icon on the desktop. 4. Pull down the "Software" menu and select "Patch Management-->Load Patch". 5. You will see the "Begin Load Patch" menu. Be sure the local machine name is selected and choose "Continue". 6. You will see the "Select Media" menu. a. If you are loading this SLS from floppy disk media, select the appropriate floppy disk drive and choose "Continue". Proceed to step 7. b. If you are loading this SLS from a media image per step 2, pull down the "Media Device" menu and select "Media Images", then choose "Continue". You will then see the "Enter Image Directory" menu. Enter /tmp and choose "OK". 7. You will see the "Load Patch Preference" menu. Choose "Full". 8. You will see the "Load Patch Progress" window. If the patch loads successfully, you will see a "Message" window that states "Load Patch complete". Choose "OK". You are then returned to the main Software Manager window. 9. To apply the patch now, continue with step 2 under section II, "Applying the Patch". To exit the Software Manager now, select "Exit" from the "Host" menu. II. APPLYING THE PATCH 1. Log in as root. Execute the command: # scoadmin software or double click on the Software Manager icon on the desktop. 2. Pull down the Software menu and select "Patch Management-->Apply Patch". 3. You will see the "Begin Apply Patch" menu. Be sure that the local machine name is selected and choose "Continue". 4. You will see the "Select Media" menu. The "Hard Disk" menu item should already be selected. Choose "Continue". 5. You will be presented with the "Select Patch-product to Apply" menu. Highlight the "Streams Lock Timeout and Protocol Data Supplement oss452a" patch and then choose "Full" to continue. 6. You will see the "Apply Patch Progress" window as the system applies the patch. 7. You will see an information window displaying the message: During this apply patch, the kernel was relinked. You must reboot your system to make this kernel effective. Click on "OK". 8. You will see a "Message" window stating "Apply Patch Complete". Choose "OK" and you will be returned to the Software Manager's main menu. Exit the Software Manager by choosing "Exit" from the "Host" menu. 9. Log in as root on tty01, and shut down the system: # shutdown -g0 -y After shutting down and rebooting the machine, application of the patch is complete. III. NOTES ON NETWORK INSTALLATION To install the patch on other SCO OpenServer 5.0.* machines over the network, first load the patch as in section I above on a designated installation server. Then create the user "swadmin" on the installation server. When running the Software Manager on the system where the patch will be installed, you will be prompted for the source location of the patch in the "Begin Load Patch" window. Be sure to choose "from another host" during this phase. You will need to provide the name of the installation server, as well as the password of the "swadmin" user on the installation server, to initiate the installation process. IV. PATCH REMOVAL NOTE: Patches must be rolled back in the reverse order in which they were installed on a per-component basis. Hence, if the "Trap F Supplement oss452a" patch is not the most recent patch applied to the UNIX component of the product, you will have to rollback all patches applied after the "Trap F Supplement oss452a" patch prior to rollback of the "Trap F Supplement oss452a" patch. If you want to remove the patch, take these steps: 1. Log in as root. 2. Execute the command: # scoadmin software or double click on the Software Manager icon in the desktop. 3. Pull down the "Software" menu and select "Patch Management-->Rollback Patch". 4. You will see the "Begin Rollback Patch" menu, and be asked to select patched software to rollback. Select "SCO UNIX System V Operating System" and choose "Continue". 5. You will see the "Patch Selection" window. Make sure that the "Trap F Supplement oss452a" patch is selected, and choose "Continue". 6. You will see the "Confirm Selected Patches" window. Choose "Rollback" to confirm removal of the "Trap F Supplement oss452a" patch. 7. You will see the "Rollback Progress" window, as the system performs the rollback of the patch. 8. You will see an information window displaying the message: NOTE: During this rollback, the link kit wll be updated. Afterwards you must relink your kernel and reboot your machine in order to make this rollback effective. Press return to continue: 9. After pressing the key, you will see the "Rollback Progress" window, after which a "Message" window stating "Rollback Patch Complete" appears. Choose "OK" and you will be returned to the Software Manager's main menu. Exit the Software Manager by choosing "Exit" from the "Host" menu. 10. Log in as root and relink the kernel: # cd /etc/conf/cf.d # ./link_unix -y 11. Log in as root on tty01, and shut down the system: # shutdown -g0 -y After shutting down and rebooting the machine, rollback of the patch is complete. 12. To also unload the patch, making it no longer available to be applied, follow the steps in this section. In step 3, choose: "Patch Management-->Unload Patch" instead of: "Patch Management-->Rollback Patch" If you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier. We appreciate your business. SCO Support Services