Dear SCO Customer, Enclosed is Support Level Supplement (SLS) xnx166. This SLS contains a device driver for the following Tecmar/Wangtek tape drive/controller combinations running with the SCO XENIX 386 Operating System Release 2.3.2 for computers based on Micro Channel Architecture (MCA): Tape Drive Tape Controller ========== =============== QT 60E 60 Megabyte External Tecmar MC Single Chip Qic-02 Host Adaptor QT 90E 90 Megabyte External Tecmar MC Single Chip Qic-02 Host Adaptor QT 125E 125 Megabyte External Tecmar MC Single Chip Qic-02 Host Adaptor QT 150E 150 Megabyte External Tecmar MC Single Chip Qic-02 Host Adaptor 5099EG 60 Megabyte Internal Wangtek PC-02 Single Chip Host Adaptor 5125EG 125 Megabyte Internal Wangtek PC-02 Single Chip Host Adaptor 5150EG 150 Megabyte Internal Wangtek PC-02 Single Chip Host Adaptor LS5099EN 60 Megabyte External Wangtek PC-02 Single Chip Host Adaptor LS5150EQ 150 Megabyte External Wangtek PC-02 Single Chip Host Adaptor Remember that you must update your Micro Channel machine's configuration information before it will allow you to run XENIX with the Tecmar/Wangtek Micro Channel Single Chip Qic-02 Host Adaptor installed. The setup/configuration routine is slightly different on various Micro Channel machines, but they all have a way to copy configuration files from option diskettes so that added cards may be recognized by the machine's setup program. Refer to the hardware manual for your machine to determine how it is done in your particular case. This operation is necessary for DOS as well as XENIX. The Tecmar option diskette is called a Tecmar Quality Tape Operating Software Diskette. The Wangtek option diskette is called a SYTOS Tape Operating System Software Diskette. Once you have configured your machine so that it is aware of the tape adaptor card, you can proceed with the installation of SLS xnx166. Be aware that you need to configure your tape adaptor card so that it is using a free interrupt vector. Below is a list of typically used interrupts: Interrupt Used For --------- -------- 0 Clock 1 Console 2 (25) Network Cards 3 Serial COM2 4 Serial COM1 5 Parallel LP2 6 Floppy Drive 7 Parallel LP0 or LP1 SCO XENIX Tape Driver Install ============================= To install SLS xnx166, log in as root, insert the floppy into your floppy drive and type: /etc/install You will see the message: First Floppy? (y/n) Answer "y" and then enter . At the next menu pick the option to: Install a Tape Driver A second menu will come up and you should pick the option to: Install Cartridge Tape Driver A third menu will come up, asking you to display, modify, select previous, or take default tape parameters. Type "q" for quit and you will see the message: Updating system configuration. Installing tape driver. Picking "q" allows the tape driver to automatically use the tape controller's parameters based on how they were defined when you updated your Micro Channel machine's configuration information. Choose "q" for quit at the final menu. You will see the message: "You must create a new kernel to effect the driver change you specified. Do you wish to create a new kernel now? (y/n)" Choose "y" and you will see the message: Re-linking the kernel... This will take a moment and then you will be asked: Do you want this kernel to boot by default? Answer "y" and when you receive a root prompt, type: /etc/haltsys to reboot your system and activate the new kernel with the tape driver linked in. Your original kernel has been renamed "xenix.old." If you ever need to boot your original kernel, after a system crash for example, just type "xenix.old" at the "boot:" prompt. Setting Up Your Tar and Backup Default Files ============================================ (1) /etc/default/tar ---------------- There is a default file for tar that is very useful for writing to tape devices. To make use of it, edit the file to indicate what size your tape is. The default file is "/etc/default/tar"; an example is included below: # @(#) def96.src 1.5 88/05/27 # device block size tape archive0=/dev/rfd048ds9 18 360 n archive1=/dev/rfd148ds9 18 360 n archive2=/dev/rfd096ds15 10 1200 n archive3=/dev/rfd196ds15 10 1200 n archive4=/dev/rfd096ds9 18 720 n archive5=/dev/rfd196ds9 18 720 n archive6=/dev/rfd0135ds18 18 1440 n archive7=/dev/rfd1135ds18 18 1440 n archive8=/dev/rct0 20 0 y archive9=/dev/rctmini 20 0 y # The default device in the absence of a numeric or "-f device" argument archive=/dev/rfd096ds15 10 1200 n Notice that the device "/dev/rct0" for cartridge tapes already exists within the "/etc/default/tar" file. You need to go into the file with an editor (/bin/vi, for example) and put in a size for the "/dev/rct0" entry. The size should be stated in 1 Kilobyte blocks, so that for a 60 Megabyte drive the size would be 60000 and your entry would look like the following: archive8=/dev/rct0 20 60000 y The reason this is useful is that it greatly simplifies your tar command because the default file provides a device name, a blocking factor and a tape size. Thus, your tar command can be condensed to the following: tar cv8 /etc A 60 Megabyte tape drive and the "/etc" directory have been used as an example. As you can see, simply using the "8" acts as a pointer to the default file, so that you don't need to specify as much on the command line. To list your tape after writing to the tape drive, the command would be: tar tv8 and to extract your files, the command would be: tar xv8 /etc which would bring over the whole "/etc" directory from tape, or as a variation, you can specify any particular file. For example, your command could be: tar xv8 /etc/termcap (2) /etc/default/archive -------------------- Another very useful file, "/etc/default/archive" is used by "sysadmin," a menu driven "front end" to the command "/etc/backup." Again, all you need to do is edit the file "/etc/default/archive" and indicate a size for the "/dev/rct0" entry. The "/etc/default/archive" file entry for a cartridge tape drive using a standard 600 foot tape is included below: # @(#) archive.src 1.6 88/03/21 # # Copyright (C) The Santa Cruz Operation, 1986. # This Module contains Proprietary Information of # The Santa Cruz Operation, Microsoft Corporation # and AT&T, and should be treated as Confidential. # cdev=/dev/rct0 desc="Cartridge Drive (600 ft tape)" \ blocking=20 size=600 density=20000 The actual file on your system will have many entries for various floppy devices as well. You will need to locate the above entry in the file. Again, using a 60 Megabyte tape drive as our example, your edited entry should look like the following: cdev=/dev/rct0 desc="Cartridge Drive (600 ft tape)" \ blocking=20 size=60000 NOTE: It is recommended that you use somewhat less than the full tape ==== capacity when you indicate a size. This is to compensate for potential bad spots on the physical tape which need to be mapped out. The following values are recommended: 60 Megabyte = 59000 125 Megabyte = 123000 150 Megabyte = 148000 If you have any questions please call the SCO Customer Services Department at (800) 347-4381. SCO Customer Service is available Monday through Friday 6:00 A.M. to 5:00 P.M. Pacific Time. We appreciate your business. SCO Support Services