Dear SCO Customer, Support Level Supplement xnx102 is only necessary if you are trying to configure multiple Mountain tape drives with SCO XENIX Operating System Release 2.3.1, or 2.3.2. If you are simply configuring a single Mountain tape drive, the device driver is already available in your system and all you need to do is type: /etc/mkdev tape and follow the instructions for adding a tape drive in Chapter 16 of your SCO Installation and Maintenance Guide. The default settings for the Mountain tape controller board for DMA channel, interrupt channel and Base Address are: XENIX DMA Interrupt Base Controller Board Channel Vector Address Type ==================================================================== Mountain QIC-02 1 3 28cH 5 Be aware that the default setting for the Mountain controller board uses interrupt 3, which is the same interrupt used by Com 2. If you have a Com 2 port, you must set the tape controller for a different interrupt (2, 4, or 5). Interrupt 4 is used by Com 1 and interrupt 5 is used by lp2. If you use interrupt 2 you should indicate that the interrupt is "25" when you run "mkdev tape". Insert your tape controller board and follow the instructions below. 1. Run the SCO XENIX install program by typing "/etc/install" at a superuser prompt. The following prompt will be displayed: First Floppy (y/n) Insert the SCO XENIX Mountain tape driver diskette and answer "y" (yes) to the above prompt. When the install process is done, a "mkdev tape" command will automatically be issued. 2. Once the "mkdev tape" command is issued, select "1 Install Cartridge Tape Driver" from the first menu. If you have changed the base address, DMA or interrupt channel settings on your tape controller board, select "2 Modify tape parameters" from the second menu, and modify the appropriate parameters. If you haven't changed any board settings, or you are finished modifying parameters, select "1 Display tape parameters" from the second menu, and verify that the tape parameters are correct. Once you have verified the tape parameters, select "q" (for quit) at the second menu. Select "q" again at the first menu. Answer "y" to the question, "Do you wish to create a new kernel now?" Answer "y" to the question, "Do you want this kernel to boot by default?" You'll then be prompted for more floppy diskettes. Answer "n" to this prompt. 3. Now you should reboot your system to run the new kernel. During the booting process, the streaming cartridge tape and associated parameters will be identified on your boot screen. If you need to change the DMA, Interrupt or Base Address settings you need to physically move jumpers or switches on the tape controller board. Use the Mountain SETBOARD program (PC-DOS) to identify which jumpers or switches you need to move. Note that the "XENIX Controller Type" number shown above is different from the number used for the type of controller board for the SETBOARD program (refer to Appendix B of your Tape Software User's Guide to identify your controller type for SETBOARD). Once the changes have been made and the board is installed, you must also use the XENIX "mkdev tape" program to "Modify tape parameters." 4. To confirm that there are no interrupt or base address conflicts between your tape system and other devices in your computer system, issue the following commands as a test: tape reset tape rewind tape status The tape should be rewound after the tape rewind command. After the tape status command, the following should be displayed: status: beginning-of-tape soft errors: 0 underruns: 0 If your system hangs instead of displaying the status, this means there are conflicts in either the interrupt channel or base address. Such conflicts must be resolved by changing the interrupt or base address as described in step 3, before going on to step 5. 5. You may now exercise your Mountain tape unit. This command copies the "/etc" directory from the hard disk to the tape drive: tar cvf /dev/rct0 /etc This command lists the files written to tape by the previous example: tar tvf /dev/rct0 This command restores the "/etc" directory from the tape drive to the hard disk: tar xvf /dev/rct0 6. Creation of Multiple Tape Devices ================================= You will need to create multiple tape devices if you are configuring your system for multiple Mountain tape drives. Use the "/etc/mknod" command to make your desired tape devices. The following is an example device for one tape drive in QIC-24 format that rewinds: /etc/mknod /dev/rct0 c 10 0 "rct0" is the name of the sample tape device. The letter "c" should always be included. The major number for tape devices is always 10. The minor number is a decimal number that represents the following 8 bits (HI true): bit 0 = 1st tape drive on-line bit 1 = 2nd tape drive on-line bit 2 = 3rd tape drive on-line bit 3 = don't rewind tape following tape close bit 4 = select format (0 = QIC 24, 1 = QIC 11)* bit 5 = 4th tape drive on-line bit 6 = increase memory allocation** bit 7 = set maintenance mode * only QIC 24 is supported on Mountain boards ** increases buffer allocation for tape driver, so operations will be performed faster (For information about converting binary numbers to decimal, see the last page of these instructions.) If bits 0, 1, 2 and 5 are off, as in the example above, the 1st drive will be the active drive. As an example of a tape device for two tape drives with increased buffer allocation and no-rewind, the "mknod" minor number would be: 01001011 = 75 This would be used as: /etc/mknod /dev/nrctb12 c 10 75 Note that since there is no-rewind for the above device, an operation performed after this device is used will start at the point on the tape where the "nrctb12" device stopped. The following is an example of a tape device for four tape drives: /etc/mknod /dev/rct1234 c 10 39 The following is an example of a tape device for two tape drives with no-rewind after tape close: /etc/mknod /dev/nrct12 c 10 11 The following is an example of a tape device for two tape drives that does rewind after tape close: /etc/mknod /dev/rct12 c 10 3 As an example of how no-rewind and rewinding tape devices can be used, the following example backs up three volumes on a two-drive tape system: tar cvf /dev/nrct12 /etc tar cvf /dev/nrct12 /usr tar cvf /dev/rct12 /bin After the first volume is backed up onto the first tape, the tape will halt. The second tar command will back up the second volume from that location on the tape on. If the volumes are larger than the first tape, the backup will be continued onto the tape in the second drive. The third tar command will back up the third volume and then rewind the current tape. If you wanted to list the files in the above tape volumes, in a similar manner you'd use the following commands: tar tvf /dev/nrct12 /etc tar tvf /dev/nrct12 /usr tar tvf /dev/rct12 /bin Note that another item in this database presents a more thorough treatment of no-rewind devices. Converting Binary Numbers to Decimal ==================================== Binary to Decimal Table 00000001 = 1 00000010 = 2 00000100 = 4 00001000 = 8 00010000 = 16 00100000 = 32 01000000 = 64 10000000 = 128 In the earlier example for "nrctb12", the bits that make up the minor number for dev/nrctb12 are 01001011. If you add up the decimal values for the desired factors (two drives, no-rewind, increased memory allocation), the total is 75: 1st tape drive: 00000001 = 1 2nd tape drive: 00000010 = 2 no-rewind 00001000 = 8 increased memory 01000000 = 64 -------- --- 01001011 75 If you have any questions, please call our Customer Services Department at (800) 626 - 4381. SCO Customer Service is available Monday through Friday, 6:00 A.M. to 5:00 P.M., Pacific Standard Time. We appreciate your business. SCO SoftCare Support Services