Dear SCO Customer, Support Level Supplement (SLS) CMW498A, the CMW+ Hard Disk Controller BTLD, contains support for additional HD BTLDs. This SLS consists of a replacement wd driver for SCO CMW+ Open Desktop System Release 3.0.1. The enhanced wd driver provides support for ATAPI (IDE) CD-ROM drives. It also corrects installation errors such as "WARNING: hd: no root device" and "/initscript: /dev/hd00: cannot open." This support is available at, or after, installation time. IMPORTANT: Do NOT use SLS CMW498A with SLS CMW490A. Note that SLS CMW498A should only be installed on a computer with an IDE CD-ROM and SCSI hard disk. If, instead, your system has a SCSI CD-ROM and SCSI hard disk, the original N1 diskette should be used for installation. Or, if your system contains an IDE CD-ROM and an IDE hard disk, use the replacement N1 diskette in SLS CMW490A, available for download from SCO's ftp site. INSTRUCTIONS AT INSTALLATION TIME 1. Boot the system from the SCO-supplied standard N1 boot floppy. 2a. At the Boot: prompt, type the following, if the boot disk device is attached to a SCSI host adapter: defbootstr link=" xwd" hd= Srom=wd(,,) where is replaced by the actual SCSI BTLD name, is replaced by Sdsk for SCSI, or ida0 for Compaq IDA, and , , and are replaced by 0 or 1 as follows: HA# is 0 or 1 and refers to the number of the ATAPI controller; ID is 0 or 1 and 0 refers to the CD-ROM as master and 1 as slave; LUN is 0 or 1 and is the LUN of the ATAPI CD-ROM drive (always 0). NOTE: " xwd" must be entered in that order and enclosed in quotation marks. For example, a common bootstring for a system with the boot disk device attached to a Compaq integrated SCSI host adapter, and the CD-ROM drive attached to the primary IDE controller as master device, would be: defbootstr link="CUCHA xwd" hd=Sdsk Srom=wd(0,0,0) 2b. At the Boot: prompt, type the following, if the boot disk device is attached to an IDE controller: defbootstr link=xwd Srom=wd(,,) where , , and are replaced by 0 or 1 as described in 2a above. For example, a common bootstring for a system with the boot disk device attached to an IDE controller, and the CD-ROM drive attached to the secondary IDE controller as master device, would be: defbootstr link=xwd Srom=wd(1,0,0) 3. Follow all the prompts on the screen. You will see "Characteristic h not supported, ignore." This message can be safely ignored. 4. The installation options in this step only apply if you are installing on a disk larger than 2GB. If you are not installing on a disk larger than 2GB, skip this step and answer the installation questions as you normally would. In the "Hardware Setup" screen, you will see the choices "Preserve" or "Overwrite". If you _are_ installing on a disk larger than 2GB: - You must choose the "Preserve" option during installation. You cannot use the "Overwrite" option. Do NOT Scan for bad tracks. If you have already attempted to scan for bad tracks, and the hard drive is greater than two gigabytes (2GB), delete the entries in the Current Bad Track. To delete the badtrk entries: - Select option six (6). - Delete all entries from the Current Bad Track Table. - Enter 'q' to quit and press to accept the default value for the bad track space allocation. - When prompted: "Do you wish to update this device with the new table? (y/n)," enter 'y' to update device with the new table. - When prompted: "Do you want to attempt to salvage ...(y/n)," enter 'n'. 5. In the "Hardware Setup" screen, when prompted for installation media, press for additional choices. You will see the choice "SCSI Tape." Press again for more choices. Highlight and select "SCSI CD-ROM." You will be in the "Installation Media Setup" screen. The only value that can be changed in this screen is the "SCSI ID" value. Press for choices. Highlight and select the value 0, if the ATAPI CD-ROM is configured as a master device. Select 1, if configured as slave. Continue the installation as instructed in the standard SCO documentation and onscreen prompts. 6. In the screen "Filesystem Setup", adjust filesystem sizes if necessary to assure that no filesystem is greater than 2 Gigabytes (2048 MB). When you exit this screen, you may see these messages: WARNING: Multiple SCSI host adapters detected WARNING: Using SCSI host adapter for installation where is the BTLD driver name used in step 1 above. You can safely ignore these messages. 7. Next, you will be prompted to boot from the N1 floppy a second time. At the Boot: prompt, enter the identical bootstring as in step 2a or 2b above, instead of pressing , as the onscreen message indicates. Continue to follow the onscreen prompts. When prompted "Do you want to replace the existing wd driver?", answer "yes". 8. To use the CD-ROM after installation, run "mkdev cdrom" to configure your CD-ROM drive. Select wd as the adapter name. Edit the file /etc/default/boot to change the line defining DEFBOOTSTR so that it does not contain any "hd" or "Srom" references. INSTRUCTIONS FOR INSTALLING ON AN INSTALLED SYSTEM 1. Insert the SLS CMW498A floppy in the floppy drive. 2. Type "/usr/bin/installpkg" and follow the onscreen instructions. 3. Type "cd /etc/conf/cf.d". 4. Type "./link_unix -y". 5. To use the CD-ROM after installation, run "mkdev cdrom" to configure your CD-ROM drive. Select wd as the adapter name. Edit the file /etc/default/boot to change the line defining DEFBOOTSTR so that it does not contain any "hd" or "Srom" references. If you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier.