Dear SCO Customer: Support Level Supplement (SLS) app196 allows ASCII text files to be printed on PostScript printers under SCO Professional Release 2.0.0 and SCO FoxBASE+ Release 2.1.1. SLS app196 is not intended to be a general purpose ASCII to PostScript translator. It is produced with the purpose of handling the most common printing situations. To install SLS app196, perform the following steps: 1. Log in as root on the machine where the SCO application(s) is installed. Note: If you have the applications installed on more than one machine or more than one filesystem location, you will have to run this procedure more than once. 2. Type the following command to change directories: cd /tmp 3. Insert the cartridge tape or floppy disk into the drive. 4. To extract SLS app196, enter the following command, where is the name of the device that corresponds to your tape or disk drive. tar xvf For more information on the device name to use, consult your operating system documentation, your system administrator, or the table below: ---------------------------------------- Media Device Name ---------------------------------------- cartridge tape /dev/rst0 3 1/2" 135 tpi dshd /dev/fd0a 5. At the operating system prompt, type the following command and press . ./installprint 6. You should see a message similiar to the following: page 1 ======================================================================== | | You must be root to install this fix correctly. | You must be on the machine where the SCO application(s) | have been installed. | If you have the application(s) installed on more | than one machine you will have to run this procedure | more than once. | If you have the application(s) installed in more than | one filesystem location you will have to run this | procedure more than once. | For additional information please refer to the cover letter. | | Do you wish to continue the installation? (y/n)? ======================================================================== Enter 'y' if you want to continue with the installation. Enter 'n' to terminate the installation. 7. If you choose 'y' to continue the installation, you will then see the following message: ======================================================================== | Enter the path from / to your installation directory. | For example: If you installed SCO Professional | at /home/sco. Your would enter: | /home/sco | Enter the installation path. Enter q to quit. ======================================================================== For example, if the files /home/sco/usr/bin/foxplus and /home/sco/usr/lib/foxplus/foxplus.pr exist, then the installation directory would be /home/sco. 8. If the application does not exist, you will again be prompted for the correct path. See step 7 for more information. If the application(s) exists in the installation path given, you will see a message similiar to the following: ======================================================================== | install path is | | SCO FoxBASE+ found to be installed at this location. | Fox update is now installed. | | SCO Professional found to be installed at this location. | Pro update is now installed. | New driver file already in place. ======================================================================== page 2 9. SLS app196 should now be installed. It is highly recommended that you test the newly installed SLS. Type 'y' followed by a when you see the following prompt: ======================================================================== | | Do you want to test the new driver with the printer? (y/n)? | ======================================================================== Enter the PostScript Printer's destination name as lpr would expect it after the -P option. ======================================================================== | | Enter the name of the printer. | Enter quit to complete the installation. ======================================================================== To end the installation type 'quit' followed by . You may test more than one printer at this time by entering another printer name when the test cycles back through to this question again. 10. Your printout should appear as follows: ======================================================================== | | #You will need a printcap entry that looks | #similar to this to use the text2post driver | lwsco|pssco|:\ | :lp=/dev/ttya:sd=/usr2/usr/spool/lwsco:\ | :lf=/usr2/usr/spool/lwsco/lwsco-log:af=/usr2/usr/adm/lwsco.acct:\ | :br#9600:rw:fc#0000374:fs#0000003:xc#0:xs#0040040:mx#0:sf:sb:sh: | ======================================================================== 11. If you did not receive a printout or the printout did not match the above, verify that you used the correct printer name and try printing again. 12. You are now asked if you would like to print out the readme files. These files contain information on how to implement the SLS for SCO Professional and SCO FoxBASE+. Both readme files will be printed. If these instructions are not printed, you will have to open a separate window to read the files while implementing the SLS for each application. You now have completed the installation of SLS app196. If you have any questions, please call our SCO Customer Services Department at (800) 347-4381. SCO Customer Service is available Monday through Friday, 6:00 A.M. to 5:00 P.M., Pacific Time. We appreciate your business, SCO Support Services SK/mhj:3-90 page 3