HP(r) DAT Supplement Release and Installation Notes Version 1.0.0 30 January 1991 1. Preface The HP DAT (Digital Audio Tape) Supplement provides your SCO(r) UNIX(r) System V/386 Release 3.2 Version 2.0 with additions to the standard SCSI tape device driver. (A device driver is a software pro- gram that is configured into the UNIX operating system to provide an interface to a specific kind of hardware device.) These additions enable your computer to use the full capabilities of the Hewlett Packard(r) DAT device. The HP DAT Supplement extends DDS (Digital Data Storage) functionality for the operating system. DDS is the standard data storage format for 4-mm DAT devices. This extended support includes the following features: o The HP DAT device is tested and integrated with the SCO SCSI tape device driver. In previous releases, the HP DAT device's extended status mes- sages were not recognized by the operating system and were returned instead as errors. o This supplement supports the ``fast search'' capabilities of the DDS format on HP DAT devices. The DDS format encodes special data separator marks (setmarks) on the tape in such a way that they can be located more quickly than by reading the data sequentially (as most tape devices are required to do). The HP DAT device can position a tape to a set- mark up to 200 times faster than by sequential data access methods. o This supplement supports DDS tape partitions on HP DAT devices. The DDS format allows you to create two partitions on a single tape. These partitions are logically separate and can be read and written independently (but not simultaneously). You can archive two separate filesystems on one tape. You can also use one partition for storing a file listing of a file archive and use another partition for storing the actual archive. Each tape may be formatted with different, fixed partition sizes. 2. Release Contents This distribution includes the following: o one distribution floppy diskette 30 January 1991 - 1 - The Santa Cruz Operation, Inc. Release Notes o these Release and Installation Notes o a new dat(HW) manual page and modified tape(HW) and tape(C) manual pages for UNIX System V/386 Release 3.2 Version 2.0 3. Configuration Requirements You need the following resources to install and run the HP DAT Supple- ment: 30 January 1991 - 2 - The Santa Cruz Operation, Inc. HP DAT Supplement ________________________________________ |COMPUTER | an industry-standard | | | 386 or 486 computer | |________________|______________________| |OPERATING | UNIX System V/386 | |SYSTEM | Release 3.2 Version | | | 2.0 | |________________|______________________| |DISK CAPACITY | no additional | | | storage space is | | | needed for this sup- | | | plement | |________________|______________________| |RAM | no additional RAM is | | | needed for this sup- | | | plement | |________________|______________________| |SCSI CONTROLLER | a standard, sup- | | | ported SCSI con- | | | troller for UNIX | | | System V/386 Release | | | 3.2 Version 2.0 | | | | | | SCSI cards supported | | | by SCO Extended | | | Functionality Sup- | | | plements may work | | | but are unsupported | | | by this supplement. | |________________|______________________| |DAT DEVICE | an HP DAT device, | | | model number | | | HP35450A or C150xA | |________________|______________________| ********************************************************************* NOTE Although UNIX System V/386 Release 3.2 Version 2.0 supports additional DAT devices, this supplement supplies extended functionality for the HP DAT device only. ********************************************************************* 4. Installing the HP DAT Supplement After you have installed SCO UNIX System V/386 Release 3.2v2.0 and any other updates or supplements, use the following procedure to install the HP DAT Supplement. To install the HP DAT Supplement, follow these steps: 1. Reboot the system and enter single-user mode. You must be in single-user mode to install the HP DAT Supplement. 30 January 1991 - 3 - The Santa Cruz Operation, Inc. Release Notes 2. Type custom and press . The custom main menu appears with the Install option highlighted. 3. Select Install from the initial custom menu by pressing . A new menu appears. 4. Choose A New Product from the next menu by pressing . A new menu appears. Press to choose the option Entire Product from the displayed menu. This selection installs the HP DAT Supplement package. You are prompted to insert distribution volume 1. 5. Insert the HP DAT Supplement diskette into floppy drive 0 and press to continue. You see the messages Installing custom data files... and Creating file lists.... You are prompted to install the HP DAT Supplement floppy volume 1. 6. Check that the diskette is properly inserted and press to continue. You see the messages Extracting Files... and Exe- cuting HP DAT Supplement Init Script. This message appears: --------------------------------------------- begin screen display --- The HP DAT SCSI Device is not configured into the kernel. Do you wish to install it now? (y/n) --------------------------------------------- end screen display ----- 7. If you want to configure the HP DAT device now, skip to the next step. Answer n if you want to configure the HP DAT device later by using the mkdev tape utility. ********************************************************************* NOTE You cannot use the HP DAT device until it is configured into the ker- nel. ********************************************************************* If you answer n, you see the message: 30 January 1991 - 4 - The Santa Cruz Operation, Inc. HP DAT Supplement --------------------------------------------- begin screen display --- You may use "mkdev tape" to configure the HP DAT Device at some other time. HP DAT Supplement installation complete. --------------------------------------------- end screen display ----- Press to go back to custom and then press any key to return to the main menu. Select Quit. Another menu appears. Choose Yes to leave custom and then remove the distribution diskette. 8. If you answer y to configure the HP DAT device, the mkdev tape utility main menu appears: --------------------------------------------- begin screen display --- Tape Drive Configuration Program 1. Install a Tape Drive 2. Remove a Tape Drive 3. Change default Tape Drive Select an option or enter q to quit: --------------------------------------------- end screen display ----- ********************************************************************* NOTE The system is configured by default with a cartridge tape drive and a SCSI tape drive (ID 2). If you want to link the HP DAT device to the default tape device /dev/rct0, use mkdev tape at this point in the installation to remove the cartridge tape driver before you configure the HP DAT device. If you want to configure your HP DAT device as SCSI ID 2, use mkdev tape to remove the SCSI tape configured at that location. For more information, please see Chapter 8, ``Using Floppy Disks and Tape Drives,'' in the SCO UNIX System V/386 Operating System Administrator's Guide. ********************************************************************* To install the HP DAT device, choose the option Install a Tape Drive. The following menu appears: --------------------------------------------- begin screen display --- 30 January 1991 - 5 - The Santa Cruz Operation, Inc. Release Notes Tape Drive Installation Menu 1. Install Cartridge Tape Drive 2. Install Mini-cartridge Tape Drive 3. Install Qic-40 Tape Drive 4. Install SCSI Tape Drive 5. Install SCSI HP DAT Drive Select an option or enter q to return to the main menu: --------------------------------------------- end screen display ----- 9. Choose the option Install SCSI HP DAT Drive. This message appears: --------------------------------------------- begin screen display --- The SCSI HP DAT Drive must be configured before use. Do you wish to configure the SCSI HP DAT Drive now? (y/n) --------------------------------------------- end screen display ----- 10. If you want to configure the drive, skip to step 13. If you answer n, this message appears: --------------------------------------------- begin screen display --- The SCSI HP DAT Drive has been added to the system configuration files. However, /etc/conf/cf.d/mscsi must also be updated before using a SCSI HP DAT Drive. It is advisable to reinvoke mkdev tape accomplish this. --------------------------------------------- end screen display ----- The mkdev tape main menu appears. 11. Choose q to leave mkdev tape. You see the message HP DAT Sup- plement installation complete. 12. Press to go back to custom and then press any key to return to the main menu. Select Quit. Another menu appears. Choose Yes to leave custom and then remove the distribution diskette. 30 January 1991 - 6 - The Santa Cruz Operation, Inc. HP DAT Supplement 13. Enter y to configure the HP DAT drive now. This prompt appears: --------------------------------------------- begin screen display --- What is the ID of the controller for this device? Select 0-7, or 'h' for help, or 'q' to quit: --------------------------------------------- end screen display ----- Refer to your hardware manual for information about selecting the SCSI device location for your HP DAT device. Locations 2-6 are recommended. 14. Enter the controller ID number. This prompt appears: --------------------------------------------- begin screen display --- Which SCSI host adapter supports this device? Select 0 or 1, or 'h' for help, or 'q' to quit: --------------------------------------------- end screen display ----- 15. Enter the number of the supporting host adapter. Now this prompt appears: --------------------------------------------- begin screen display --- What is the LUN of this device? Select 0-7, or 'h' for help, or 'q' to quit: --------------------------------------------- end screen display ----- 16. Choose 0. Now you see the message The SCSI configuration has been updated. A list of special device files appears, followed 30 January 1991 - 7 - The Santa Cruz Operation, Inc. Release Notes by a list of file links to the default SCSI tape device loca- tions: --------------------------------------------- begin screen display --- The following special device files have been created: Tape Partition 1 Tape Partition 2 ================ ================ /dev/urStp0.0 /dev/urStp0.1 (Unload, Rewind) /dev/nurStp0.0 /dev/nurStp0.1 (Rewind, No Unload) /dev/nrStp0.0 /dev/nrStp0.1 (No Rewind) /dev/xStp0.0 /dev/xStp0.1 (Control) For convenience, the following links to traditional SCSI tape device names have also been created: /dev/rStp0 linked to /dev/nurStp0.0 /dev/rStp0.0 linked to /dev/nurStp0.0 /dev/rStp0.1 linked to /dev/nurStp0.1 /dev/nrStp0 linked to /dev/nrStp0.0 /dev/xStp0 linked to /dev/xStp0.0 /dev/urStp0 linked to /dev/urStp0.0 Press to continue. --------------------------------------------- end screen display ----- 17. Press to continue. If a cartridge tape drive is configured on your system, the fol- lowing message appears: --------------------------------------------- begin screen display --- The presence of a Cartridge Tape Drive has been detected. the Cartridge Tape Drive must use the default devices to function properly. Therefore, SCSI devices will be created without the default device links. --------------------------------------------- end screen display ----- The mkdev tape main menu appears. Skip to step 23. 18. If there is another SCSI tape device linked to the default tape locations, the following prompt appears: --------------------------------------------- begin screen display --- 30 January 1991 - 8 - The Santa Cruz Operation, Inc. HP DAT Supplement Another SCSI Tape Drive is currently linked to the default device /dev/xct0. Would you like the current SCSI Drive linked to the default devices? (y/n) --------------------------------------------- end screen display ----- 19. If you answer n, the mkdev tape main menu appears. Skip to step 23. To link the default device to the current SCSI drive, answer y. The following message appears: --------------------------------------------- begin screen display --- Default special devices have been created with the following links: /dev/xct0 linked to /dev/xStp0 /dev/rct0 linked to /dev/rStp0 and /dev/rmt/0b /dev/rct0 linked to /dev/nrStp0 and /dev/rmt/0bn --------------------------------------------- end screen display ----- 20. If there is no SCSI tape device linked to the default tape dev- ice locations, the SCSI tape is linked automatically to the default tape devices. The following message appears: --------------------------------------------- begin screen display --- Default special devices have been created with the following links: /dev/xct0 linked to /dev/xStp0 /dev/rct0 linked to /dev/rStp0 and /dev/rmt/0b /dev/rct0 linked to /dev/nrStp0 and /dev/rmt/0bn --------------------------------------------- end screen display ----- The mkdev tape main menu appears. Skip to step 23. 21. You may also see this message: --------------------------------------------- begin screen display --- 30 January 1991 - 9 - The Santa Cruz Operation, Inc. Release Notes Another SCSI Tape Drive is currently listed as the default in /etc/default/tape. Do you wish to change this to the current SCSI HP DAT Drive? (y/n) --------------------------------------------- end screen display ----- 22. Answer appropriately. The mkdev tape main menu appears: --------------------------------------------- begin screen display --- Tape Drive Configuration Program 1. Install a Tape Drive 2. Remove a Tape Drive 3. Change default Tape Drive Select an option or enter q to quit: --------------------------------------------- end screen display ----- 23. Select q to quit. This prompt appears: --------------------------------------------- begin screen display --- You must create a new kernel to effect the driver change you specified. Do you wish to create a new kernel now? (y/n) --------------------------------------------- end screen display ----- 24. If you want to create a new kernel, skip to the next step. If you answer n, the following message appears: --------------------------------------------- begin screen display --- To create a new kernel, execute /etc/conf/cf.d/link_unix. Then you must reboot your system by executing /etc/shutdown -i0 before the changes you have specified will be implemented HP DAT Supplement installation complete. Press to continue... --------------------------------------------- end screen display ----- 30 January 1991 - 10 - The Santa Cruz Operation, Inc. HP DAT Supplement Press to go back to custom and then press any key to return to the main menu. Select Quit. Another menu appears. Choose Yes to leave custom and then remove the distribution diskette. 25. Enter y to relink the kernel. This message appears: --------------------------------------------- begin screen display --- The UNIX Operating System will now be rebuilt. This will take a few minutes. Please wait. Root for this system build is /. The UNIX kernel has been rebuilt Do you want this kernel to boot by default? (y/n) --------------------------------------------- end screen display ----- 26. Enter y. You see the message: --------------------------------------------- begin screen display --- Backing up /unix to /unix.old Installing new /unix The kernel environment includes device node files and /etc/inittab. The new kernel may require changes to /etc/inittab or device nodes. Do you want the kernel environment rebuilt? (y/n) --------------------------------------------- end screen display ----- 27. Enter y. You see messages confirming the kernel linking. The message The HP DAT Supplement installation complete appears. 28. Press and then any key to go back to custom. You see the message Checking file permissions... and then the custom menu appears. 29. Select Quit to leave the custom menu, and then choose Yes to leave custom. 30 January 1991 - 11 - The Santa Cruz Operation, Inc. Release Notes 30. Remove the HP DAT Supplement diskette from the floppy drive. 31. Enter shutdown -g0 -y to reboot your system and effect the con- figuration changes that you made during the installation pro- cedure. The operating system kernel is now configured to use the HP DAT device. 5. Removing the HP DAT Supplement The HP DAT Supplement is not designed to be removed. 6. Notes The following sections describe issues you should be aware of concern- ing the HP DAT Supplement. 6.1 Reinstalling the Link Kit If you need to reinstall the Link Kit after you have installed the HP DAT Supplement, you must reinstall the supplement and configure the HP DAT device. 6.2 Supported Media This supplement supports the standard, 60-meter Digital Audio Tape media. 6.3 Problems with tar and Reaching End of Media If you expect to overflow the partition in which you are writing, use the cpio -K command rather than tar(C). Refer to the section ``Speci- fying Volume Sizes with cpio'' later in these notes for information about using cpio -K. 6.4 IMPORTANT: Data Storage Capacity As with any storage media, the effective storage capacity of the HP DAT device may be less than the maximum theoretical limit of 1.3 Giga- bytes. Possible causes are error correcting information and bad tape blocks. To ensure reliable data storage, we strongly advise that you modify the /usr/lib/sysadm/schedule file and change the size specified in the HP DAT entry from 1300000 to 1100000. See the section ``Using sysadmsh for System Backups'' later in these notes for instructions on how to modify the schedule file and for a display of the HP DAT device entry. 6.5 Differences Between HP DAT Devices and Standard SCSI Tape Devices 30 January 1991 - 12 - The Santa Cruz Operation, Inc. HP DAT Supplement The following command is not supported on the HP DAT device: o tape reten The following commands are not supported on the HP DAT device or on standard SCSI tape devices: o mt(C) o tape amount o tapecntl(C) The following commands are supported only on the HP DAT device. Do not use these commands on standard SCSI tape devices: o tape rsm o tape wsm o tape eod o tape partition 6.6 Device Minor Numbers The device numbers for the HP DAT drive are located in the /dev direc- tory. The minor numbers for the HP DAT device differ from the minor numbers for standard SCSI tape drives. /dev/rStp0 for SCSI tapes does not have the same minor number as /dev/rStp0 for HP DAT devices. The HP DAT device numbers differ because the default /dev/rStp0 tape device for the HP DAT device is a ``no unload'' device, unlike the standard SCSI tape. Also, the HP DAT device driver selects partitions through another bit in the minor number. Some applications and/or configuration management systems may expect the minor numbering scheme to be uniform across all SCSI tape devices. To view the HP DAT device minor numbers, use the ls -l command to list device files. For example, enter: ls -l /dev/nurStp0 /dev/nrStp0.1 A device file listing appears: crw-rw-rw- 2 root other 46, 4 /dev/nurStp0.0 crw-rw-rw- 1 root other 46, 68 /dev/nurStp0.1 6.7 Using the tape Command 30 January 1991 - 13 - The Santa Cruz Operation, Inc. Release Notes If you are using tape(C) and a command (such as partition) fails, the tape command does not return an error message, and it's return value does not indicate an error. The device driver, however, may print an error message to the standard output. 6.8 Tape Distributions and the Tape Bootstring The tape install utility supplied with this supplement, mkdev tape, is derived from the tape installable version of our product (for compati- bility reasons). If you are installing this supplement on a system that was installed with floppy disks, you may see the following prompt when you are ins- talling a cartridge tape drive: In /etc/default/boot: No current boot string Enter new string, "rm" to remove string, or enter q to leave current string as is: If this prompt is not documented in your release notes, enter q to effect no changes. If this prompt is documented in your release notes, please follow the instructions there. This prompt allows you to change a configuration file so that a cartridge tape drive may be configured from the Boot: prompt. This option is only available with some SCO operating system versions. 6.9 Installing a Western Digital SCSI Controller If you are installing the HP DAT device on a WD7000 controller that is not your primary boot device, you must modify the SCSI configuration file /etc/conf/cf.d/mscsi before you relink the kernel. This file is inappropriately modified by the mkdev utility. The mkdev utility con- figures your tape drive to use an Adaptec controller if your primary boot device is not a WD7000 SCSI controller. Use your text editor to modify /etc/conf/cf.d/mscsi as follows. If your HP DAT device is configured as SCSI unit 1, you see a line that looks like this: ad Stp 0 1 0 Change the line to read: wdha Stp 0 10 30 January 1991 - 14 - The Santa Cruz Operation, Inc. HP DAT Supplement Relink the kernel by entering these two commands: cd /etc/conf/cf.d ./link_unix This links your HP DAT device driver to the proper location within the kernel, provided that you executed mkdev tape previously to create an entry in the /etc/conf/cf.d/mscsi file. Reboot your system to effect this change. 6.10 Specifying Volume Sizes with cpio When you invoke cpio, use the -K option to specify the media volume size. See the cpio(C) manual page for instructions. Using the -K option prevents cpio from hanging when it reaches the End of Tape (EOT). If this occurs, follow the instructions in the next section ,``Interrupting a cpio Transfer'' to reset the tape. 6.11 Interrupting a cpio Transfer If you press to interrupt a cpio transfer (or other types of access to the DAT device), the interrupted process may become an unk- illable process in the system. Try to reset the tape device by following this procedure: 1. open another login session on another terminal or multiscreen 2. execute the su command to become the super user 3. issue a tape command similar to the following command (this sam- ple command is for SCSI tape device /dev/rStp0): tape reset /dev/xStp0 If this does not release the process, try pressing the eject button to manually eject the tape, or reboot the system to clear the process and unlock the DAT device. 6.12 Formatting Partitions on the HP DAT Device To create two partitions on an HP DAT tape, use the following command: tape -a partition_size partition partition_size establishes the size of partition 2. The size of par- tition 1 defaults to the size of the remaining tape. Using the tape -a partition command to format two partitions on the HP DAT device may take a long time. The larger the partition that you specify, the longer time required for formatting. Therefore, if you are creating two partitions of unequal sizes, specify the smaller size on the command line. For example, if you want to create one partition that is 400 Mbytes and another that is 900 Mbytes, enter this command: tape -a 400 partition 30 January 1991 - 15 - The Santa Cruz Operation, Inc. Release Notes This command requires considerably less formatting time than the alternative, which is tape -a 900 partition. You cannot specify a partition size greater than 900 Mbytes. If you need a larger partition, subtract the size that you want from 1300 Mbytes. Specify the difference on the tape -a command line to estab- lish the size of partition 2. Partition 1 defaults to the size that you want. If you need a partition size that is 1000 Mbytes, for exam- ple, enter this command: tape -a 300 partition 6.13 Performing Backups This section discusses performing user backups with archive utilities and system backups with sysadmsh. 6.13.1 User Backups The HP DAT device operates similarly to other SCSI tape devices. The tar(C) and cpio(C) commands execute on the HP DAT device normally. 6.13.2 Using sysadmsh for System Backups The backup schedule file /usr/lib/sysadmin/schedule contains data necessary for sysadmsh to perform system backups. The schedule file includes entries that specify available media types and drive loca- tions. sysadmsh recognizes one entry to use as the backup device, and the rest are commented out by pound signs (#). The HP DAT Supplement adds an entry to /usr/lib/sysadmin/schedule. This entry includes the proper tape size for the HP DAT device: # 1.3 Gb DAT Device # media /dev/rct0 k 1300000 tape erase If your HP DAT device is linked to /dev/rct0 and you are only using one partition, use the following procedure if you want to perform sys- tem backups using sysadmsh: 1. From the sysadmsh menu, select Backups and then choose Schedule. You are placed in the /usr/lib/sysadmin/schedule file using the vi(C) text editor. 2. Comment out the default media entry by preceding the entry with a pound sign (#). 3. Activate the HP DAT device entry by removing the preceding pound sign (#). 4. Verify that all media entries except for the HP DAT media entry are commented out. 30 January 1991 - 16 - The Santa Cruz Operation, Inc. HP DAT Supplement 5. Leave vi by entering ZZ. You are returned to the Backups menu. When you next create an unscheduled backup using sysadmsh, choose Car- tridge Tape from the point-and-pick list of available backup media to backup the system on the HP DAT device. sysadmsh provides the proper values for block and volume sizes for the HP DAT device. For more information, see schedule(ADM). To perform system backups using sysadmsh if your HP DAT is not config- ured as /dev/rct0, you must perform one of the following operations: o manually enter the device location to specify the backup media when you are using sysadmsh. For instructions, see Chapter 2, ``Using sysadmsh'' in the SCO UNIX System V/386 Operating system Administrator's Guide. o edit the schedule file and add the appropriate device name entry, using existing entries as a template If your HP DAT tape is partitioned, you also must provide sysadmsh with the appropriate tape sizes for each partition. Currently, sysadmsh supports one backup device. If your tape is partitioned, each partition on the tape appears as a separate device. You can con- figure only one partition at a time. Refer to Chapter 17, ``Backing Up Filesystems,'' in the SCO UNIX Sys- tem V/386 Operating System Administrator's Guide for more information. 7. Programmer's Notes This section discusses problems accessing the HP DAT device from a C program using the UNIX system call interface. These problems do not affect user-level commands such as tar(C), cpio(C), or tape(C). The following sections address problems using multiple read( ), write( ), and ioctl( ) system calls between a single open( ) and close( ) system call sequence. 7.1 Using ioctl( ) with HP DAT Devices Although the problems described in this section effect HP DAT devices, they are generic to all SCSI tape devices. 7.1.1 Unsupported Parameters The ioctl( ) parameters MT_DSTATUS, MT_AMOUNT are not functional. 7.1.2 Buffer Flushing The SCSI tape driver internally buffers data to enhance the driver's ability to keep the tape drive streaming. Internal buffering means that every time you write to the tape, the data is not necessarily written to the tape physically but may instead be stored in an internal memory buffer. 30 January 1991 - 17 - The Santa Cruz Operation, Inc. Release Notes This buffer is only flushed (writing physically all data in memory to the tape) upon a close( ) or fclose( ) system call. Consequently, the buffer is not emptied when an ioctl( ) command (such as MT_WFM) is issued using ioctl(). Because the buffer is not flushed, data write requests and ioctl( ) commands are sent to the tape drive in a dif- ferent order than they were received by the kernel. The ioctl( ) request is sent to the tape, but the previously-written data remains in the internal buffer and is written to the tape only after the dev- ice is closed. In the worst case, the device driver can overwrite data if you use the MT_REWIND ioctl( ) command and the buffer contains data. In this case, after the MT_REWIND command, the data remains in the buffer and is written to the tape whenever the device is closed. To avoid this problem, you must close and then reopen the device before you issue an ioctl( ) command. This sequence flushes the buffer before you issue an ioctl( ) command. Note that you must close and open the device before a read( ) as well as a write( ) command. This sequence is similar to what occurs at the user-level; the device opens as the program executes and then closes as the program ter- minates. Sequential data read( ) and write( ) operate normally. The only user-level program that issues an ioctl( ) to the SCSI tape dev- ice is tape(C). tape(C) opens the device before using an ioctl( ) command, ensuring that the device was previously closed and that the buffer is empty. Therefore, no buffer flushing problem exists at the user-level. 30 January 1991 - 18 - The Santa Cruz Operation, Inc. HP DAT Supplement Release and Installation Notes Version 1.0.0 1. Preface 1 2. Release Contents 1 3. Configuration Requirements 2 4. Installing the HP DAT Supplement 3 5. Removing the HP DAT Supplement 12 6. Notes 12 6.1 Reinstalling the Link Kit 12 6.2 Supported Media 12 6.3 Problems with tar and Reaching End of Media 12 6.4 IMPORTANT: Data Storage Capacity 12 6.5 Differences Between HP DAT Devices and Standard SCSI Tape Devices 12 6.6 Device Minor Numbers 13 6.7 Using the tape Command 13 6.8 Tape Distributions and the Tape Bootstring 14 6.9 Installing a Western Digital SCSI Controller 14 6.10 Specifying Volume Sizes with cpio 15 6.11 Interrupting a cpio Transfer 15 6.12 Formatting Partitions on the HP DAT Device 15 6.13 Performing Backups 16 6.13.1 User Backups 16 6.13.2 Using sysadmsh for System Backups 16 7. Programmer's Notes 17 7.1 Using ioctl( ) with HP DAT Devices 17 7.1.1 Unsupported Parameters 17 7.1.2 Buffer Flushing 17 30 January 1991 - i - The Santa Cruz Operation, Inc.